汽配人首頁 > 問答首頁

急求磁懸浮軸承或磁懸浮飛輪英文資料及譯文

要求譯文字?jǐn)?shù)在3000字以上，謝謝??！: 問提問者：網(wǎng)友 | 2017-06-22

最佳回答

　　Magnetic Bearing　　A magnetic bearing is a bearing which supports a load using magnetic levitation. Magnetic bearings support moving machinery without physical contact, for example, they can levitate a rotating shaft and permit relative motion without friction or wear. They are in service in such industrial applications as electric power generation, petroleum refining, machine tool operation and natural gas pipelines. They are also used in the Zippe-type centrifuge used for uranium enrichment. Magnetic bearings support the highest speeds of any kind of bearing; they have no known maximum relative speed.　　Description　　It is difficult to build a magnetic bearing using permanent magnets due to the limitations imposed by Earnshaw's theorem, and techniques using diamagnetic materials are relatively undeveloped. As a result, most magnetic bearings require continuous power input and an active control system to hold the load stable. Because of this complexity, the magnetic bearings also typically require some kind of back-up bearing in case of power or control system failure.　　Two sorts of instabilities are very typically present with magnetic bearings. Firstly attractive magnets give an unstable static force, decreasing with greater distance, and increasing at close distances. Secondly since magnetism is a conservative force, in and of itself it gives little if any damping, and oscillations will cause loss of successful suspension if any driving forces are present, which they very typically are.　　With the use of an induction-based levitation system present in cutting-edge MAGLEV technologies such as the Inductrack system, magnetic bearings could do away with complex control systems by using Halbach Arrays and simple closed loop coils.　　Basic Operation　　Basic Operation for a Single AxisAn active magnetic bearing (AMB) consists of an electromagnet assembly, a set of power amplifiers which supply current to the electromagnets, a controller, and gap sensors with associated electronics to provide the feedback required to control the position of the rotor within the gap. These elements are shown in the diagram. The power amplifiers supply equal bias current to two pairs of electromagnets on opposite sides of a rotor. This constant tug-of-war is mediated by the controller which offsets the bias current by equal but opposite perturbations of current as the rotor deviates by a small amount from its center position.　　The gap sensors are usually inductive in nature and sense in a differential mode. The power amplifiers in a modern commercial application are solid state devices which operate in a pulse width modulation (PWM) configuration. The controller is usually a microprocessor or DSP.　　Applications　　Magnetic bearing advantages include very low and predictable friction, ability to run without lubrication and in a vacuum. Magnetic bearings are increasingly used in industrial machines such as compressors, turbines, pumps, motors and generators. Magnetic bearings are commonly used in watt-hour meters by electric utilities to measure home power consumption. Magnetic bearings are also used in high-precision instruments and to support equipment in a vacuum, for example in flywheel energy storage systems. A flywheel in a vacuum has very low windage losses, but conventional bearings usually fail quickly in a vacuum due to poor lubrication. Magnetic bearings are also used to support maglev trains in order to get low noise and smooth ride by eliminating physical contact surfaces. Disadvantages include high cost, and relatively large size.　　A very interesting new application of magnetic bearings is their use in artificial hearts. The use of magnetic suspension in ventricular assist devices was pioneered by Prof. Paul Allaire and Prof. Houston Wood at the University of Virginia culminating in the first magnetically suspended ventricular assist centrifugal pump (VAD) in 1999　　History　　The evolution of active magnetic bearings may be traced through the patents issued in this field. The table below lists several early patents for active magnetic bearings. Earlier patents for magnetic suspensions can be found but are excluded here because they consist of assemblies of permanent magnets of problematic stability per Earnshaw's Theorem.　　Early active magnetic bearing patents were assigned to Jesse Beams at the University of Virginia during World War II and are concerned with ultracentrifuges for purification of the isotopes of various elements for the manufacture of the first nuclear bombs, but the technology did not mature until the advances of solid-state electronics and modern computer-based control technology with the work of Habermann and Schweitzer[5]. Extensive modern work in magnetic bearings has continued at the University of Virginia in the Rotating Machinery and Controls Industrial Research Program. The first international symposium for active magnetic bearing technology was held in 1988 with the founding of the International Society of Magnetic Bearings by Prof. Schweitzer (ETHZ), Prof. Allaire (University of Virginia), and Prof. Okada (Ibaraki University).　　In 1987 further improved AMB designs were created in Australia by E.Croot but these designs were not manufactured due to expensive costs of production. However, some of those designs have since been used by Japanese electronics companies, they remain a speciality item: where extremely high RPM is required.　　Since then there have been nine succeeding symposia. Kasarda reviews the history of AMB in depth. She notes that the first commercial application of AMB’s was with turbomachinery. The AMB allowed the elimination of oil reservoirs on compressors for the NOVA Gas Transmission Ltd. (NGTL) gas pipelines in Alberta, Canada. This reduced the fire hazard allowing a substantial reduction in insurance costs. The success of these magnetic bearing installations led NGTL to pioneer the research and development of a digital magnetic bearing control system as a replacement for the analog control systems supplied by the American company Magnetic Bearings Inc. (MBI). In 1992, NGTL's magnetic bearing research group formed the company Revolve Technologies Inc[1]. to commercialize the digital magnetic bearing technology. This firm was later purchased by SKF of Sweden. The French company S2M, founded in 1976, was the first to commercially market AMB’s. Extensive research on magnetic bearings continues at the University of Virginia in the Rotating Machinery and Controls Industrial Research Program　　Magnetic bearings support moving machinery without physical contact, for example, they can levitate a rotating shaft and permit relative motion without friction or wear. Long considered a promising advancement, they are now moving beyond promise into actual service in such industrial applications as electric power generation, petroleum refining, machine tool operation and natural gas pipelines.　　The AVCON magnetic bearing permits motion without friction or wear.　　Among companies producing advanced magnetic bearing systems for industrial use is AVCON, Inc., Agoura Hills, California. AVCON offers a unique technological approach that evolved from the company's work on contracts with Lewis Research Center, and Marshall Space Flight Center. The technology developed in the NASA programs contributed to AVCON's ability to overcome the limitations of early magnetic bearing systems, namely large size and weight, high power consumption and cost. The company's product line embraces a family of very compact, lightweight, power efficient, low cost bearing systems.　　Beginning in 1989, AVCON worked with Lewis to explore the possibilities of a magnetic bearing system for the turbopump of the Space Shuttle Main Engine. NASA decided to investigate magnetic bearings, which in theory-at that time-offered multiple advantages over conventional rolling element bearings.: 回答者：網(wǎng)友

產(chǎn)品精選

我來回答